Aquasource Kitchen Faucet


aquasource kitchen faucet 1

Aquasource Kitchen Faucet

Aaron Stickley The article discusses the particular installation details for two-handle WaterSense bathroom faucets from AquaSource. The instructions should also work for other AquaSource faucets, as well as top-mounted bathroom faucets from other manufacturers. There may be slightly different instructions for other faucet models, however. Tools and Materials You Will NeedNew FaucetBasin wrenchChannel-type pliers How to Install an AquaSource Bathroom FaucetFirst, shut off the water supply to the old faucet. Disconnect the water supply tubes from the tailpieces on the faucet, using a basin wrench or channel-type pliers. Then, remove the faucet that is currently installed in the sink. A basin wrench is the best tool to use when removing the mounting nuts holding the faucet in place. This is a good time to clean the sink and remove any old putty or hard water build-up.If you will be replacing the pop-up drain as well, now is the time when the drain trap and old pop-up should be removed so they are out of the way.Next, install the new faucet body. From the top of the sink, put the faucet into place over the three faucet openings. To fasten the faucet into place, reach under the sink and install the lock nuts onto the two threaded tailpieces. Before completely tightening the lock nuts with a basin wrench, check to make sure that the faucet is centered and straight. Connect the water supply tubes to the faucet, using channel-type pliers. It is always better to change the water supply tubes when installing a new faucet unless the existing ones are fairly new.Attach the hot and cold water supply lines to the corresponding threaded tailpieces of the faucet. To tighten the water lines, it is a good idea to use two pliers so you can hold against the shut-off valve or the faucet while tightening the supply tube connections. Be careful to not over-tighten when using pliers. To install the drain assembly, first separate the pop-up drain components. Slip the rubber washer onto the pop-up body and drop the pop-up into the sink drain opening. Position the opening for the ball rod so that it faces back. From under the sink, slip the washer and nut onto the pop-up drain body and tighten. As you tighten, check to make sure that the pop-up is centered properly in the sink opening.The next step is to install the pop-up drain stopper. Insert the stopper into the drain. Under the sink, insert the ball rod into the pop-up drain opening and tighten the sleeve to keep it in place.To install the pop-up lift rod, start by inserting it into the faucet opening. Under the sink, attach the perforated strap to the lift rod. The button on ,the strap can be pushed into open and locks into place when released. Attach the ball rod to the lift rod after adjusting the height of the stopper.With the AquaSource faucet installation complete you can put the drain trap back into place and turn the water supply back on. Checking for leaks is the final step of any faucet installation.First, turn on both the hot and cold sides of the faucet and check for leaks under the sink. Allow the water to run for a couple of minutes, as some faucet leaks are not obvious right away. Use a flashlight to look around under the sink so you don’t miss small leaks.To check for leaks at the pop-up drain, lower the stopper and fill the sink up with water. Release the water and look under the sink for leaks around the drain. Read More
aquasource kitchen faucet 1

Aquasource Kitchen Faucet

The article discusses the particular installation details for two-handle WaterSense bathroom faucets from AquaSource. The instructions should also work for other AquaSource faucets, as well as top-mounted bathroom faucets from other manufacturers. There may be slightly different instructions for other faucet models, however. Tools and Materials You Will NeedNew FaucetBasin wrenchChannel-type pliers How to Install an AquaSource Bathroom FaucetFirst, shut off the water supply to the old faucet. Disconnect the water supply tubes from the tailpieces on the faucet, using a basin wrench or channel-type pliers. Then, remove the faucet that is currently installed in the sink. A basin wrench is the best tool to use when removing the mounting nuts holding the faucet in place. This is a good time to clean the sink and remove any old putty or hard water build-up.If you will be replacing the pop-up drain as well, now is the time when the drain trap and old pop-up should be removed so they are out of the way.Next, install the new faucet body. From the top of the sink, put the faucet into place over the three faucet openings. To fasten the faucet into place, reach under the sink and install the lock nuts onto the two threaded tailpieces. Before completely tightening the lock nuts with a basin wrench, check to make sure that the faucet is centered and straight. Connect the water supply tubes to the faucet, using channel-type pliers. It is always better to change the water supply tubes when installing a new faucet unless the existing ones are fairly new.Attach the hot and cold water supply lines to the corresponding threaded tailpieces of the faucet. To tighten the water lines, it is a good idea to use two pliers so you can hold against the shut-off valve or the faucet while tightening the supply tube connections. Be careful to not over-tighten when using pliers. To install the drain assembly, first separate the pop-up drain components. Slip the rubber washer onto the pop-up body and drop the pop-up into the sink drain opening. Position the opening for the ball rod so that it faces back. From under the sink, slip the washer and nut onto the pop-up drain body and tighten. As you tighten, check to make sure that the pop-up is centered properly in the sink opening.The next step is to install the pop-up drain stopper. Insert the stopper into the drain. Under the sink, insert the ball rod into the pop-up drain opening and tighten the sleeve to keep it in place.To install the pop-up lift rod, start by inserting it into the faucet opening. Under the sink, attach the perforated strap to the lift rod. The button on ,the strap can be pushed into open and locks into place when released. Attach the ball rod to the lift rod after adjusting the height of the stopper.With the AquaSource faucet installation complete you can put the drain trap back into place and turn the water supply back on. Checking for leaks is the final step of any faucet installation.First, turn on both the hot and cold sides of the faucet and check for leaks under the sink. Allow the water to run for a couple of minutes, as some faucet leaks are not obvious right away. Use a flashlight to look around under the sink so you don’t miss small leaks.To check for leaks at the pop-up drain, lower the stopper and fill the sink up with water. Release the water and look under the sink for leaks around the drain.
aquasource kitchen faucet 2

Aquasource Kitchen Faucet

Why Aquasource? Aquasource is one of the less recognized kitchen faucet manufacturers but this does not discredit them whatsoever. What Aquasource understand is that looks are central to a faucet and they have a distinctly summery, Mediterranean feel to their construction, which only works in their favor. The majority of their faucets come bronzed and ready for easy installation within your kitchen, and what is more, they are incredibly easy to install, with multiple connectivities and a minimum amount of tools required. Listed below are the best Aquasource Faucet reviews for your browsing!
aquasource kitchen faucet 3

Aquasource Kitchen Faucet

Whilst on paper this sounds an incredibly similar faucet to the rest of the Aquasource range, this is actually an entirely different faucet altogether and is one of Aquasource’s newer faucets on offer. The appearance and overall weighting are fantastic, with beautiful looking taps sitting alongside the faucet head and it comes with two functions; the spray clean, as well as the more usual stream. Both of these generate good pressure and perform filling and rinsing with ease, and the head, which is plastic is not prone to overheating or being uncomfortable to the user.
aquasource kitchen faucet 4

Aquasource Kitchen Faucet

The next tip is that you should imagine how your kitchen looks with the faucet. With your imagination, you can re-consider or re-choose another one that may fit your kitchen better that the previous one. If you get stuck and can not decide which AquaSource Faucet is the best for your kitchen, you can also use the catalogue of AquaSource to find out the list of faucets they have to make decision easier.
aquasource kitchen faucet 5

Aquasource Kitchen Faucet

SLEEK DESIGNS TO COMPLIMENT YOUR STYLE Shop by Faucet Style Pull Down Faucets High-arching, maneuverable spray wands pull down to provide extended reach. Pull Out Faucets Streamlined, curved or angle sprayers save space, offer greater reach and ease of use. Traditional Faucets One-handle and two-handle options for a classic, contemporary or modern look. Bar & Prep Faucets Perfect for behind a bar, a secondary sink or a prep area or island. Wall Mount Faucets A clutter-free design that also works well with vessel or wall mount sinks. Pot Filler Faucets Folding, swing-arm feature extends easily to fill pots on the stove with water. What’s My Sink Configuration? Typically, you want to choose a faucet that matches number of holes in you sink – but you have options. Most new single handle faucets come with a deckplate that allow you to easily retro-fit a multi hole sink for a single handle faucet. One Hole Configuration Two Hole Configuration Three Hole Configuration Four Hole Configuration Shop by Finish Stainless Steel Nickel Chrome Bronze Pewter Copper Shop by Faucet Feature Touchless/Touch On Water Saving Faucets Adjustable Flow Rate Built-in-Water Filter LED Light Fingerprint/Spot-Resistant Kitchen faucets now offer an exciting mix of innovation, style and functionality to meet the demands of every household. At The Home Depot, you’ll find a wide-ranging selection of the best kitchen faucets available, from the top brands, all priced to fit your budget.Before making a selection, think about how your use kitchen faucet on a daily basis, from that first cup of coffee in the morning to preparing snacks, meals or entertaining guest. With this in mind, you’ll be able to choose a new faucet with the right combination of features- including handles, spout height and sprayers – to make quick work of your kitchen tasks.Knowing your sink configuration – how many holes are in your sink or counter – is also an important consideration. While most sinks have anywhere from 1-4 pre-drilled holes, this won’t limit your options. Most new faucets come with deckplates that will cover up any unused holes, so you can still install that sleek, single handle faucet on you four hole sink.Whether you’re shopping for a standard, single handle, pull down, pull out or touchless faucet to wall mounted, pot fillers and more, we’ve got kitchen sink faucets in the perfect finish and style to satisfy your needs. And if you need it installed, let on let one of dependable services professionals install your new kitchen faucet for you

Aquasource Kitchen Faucet

Aquasource Kitchen Faucet

Wallpaper Name : Aquasource Kitchen Faucet
Categories : News
Views : 65 Views
Downloads : 0
Tags :

Description : Download Aquasource Kitchen Faucet HD Widescreen Wallpaper from the above resolutions from the directory News. Posted by admin on June 3, 2017 If you don’t find the exact resolution you are looking for, then go for Original or higher resolution which may fits perfect to your desktop.

Comments